Find out what's NEW

Find out what's NEW

 

BD - Stackable directional control valves

— BDL1 is an assemblage of stackable valves, very versatile thanks to the modular design.  
— Stackable elements have been designed to be assembled in parallel connection, mounting up to 8 stackable directional valves.  
— BD* assemblies are suitable for compact applications, mainly in mobile industries and in mini-power packs.  
— The directional valves have a thickness of 28 mm and 1/8" BSP connections on working ports.
— Inlet elements have P and T ports 1/4” BSP.

 
44090 | | | | 3D
 

DXE5J - High response servo-proportional valve with feedback and integrated electronics

— The DXE5J valve is a four-way (3 + fail-safe position) servo-proportional valve where the spool moves inside a sleeve. It is operated by a proportional solenoid highly dynamic, which achieves high performance and not requires pilot pressure. The spool position is controlled by a linear transducer (LVDT) in closed loop, which ensures high precision and repeatability.
— It is available with two flow ranges up to 100 l/min with spools with zero overlap.
— The valve is featured by integral electronic based on SMD technology which ensures standard regulations and simplifies the electric wiring. The unit does not require any adjustment other than the possible electronic regulation of the zero.
Two types of integrated electronics are available, with analogue or fieldbus interfaces.
— Suitable for control applications with closed loop of position, velocity and pressure. If the valve is not powered or is without the enable input (Version A only), the spool moves automatically at fail-safe position.

 
85220 | | | | 3D
 

EDM-J* - Digital amplifier for closed loop continuous control valves

— The EDM-J* card is a digital amplifier intended for closed loop control of single solenoid or double solenoids proportional and servo-proportional valves.
— The card controls the position of the spool of the valve according to the reference signal, ensuring linear regulation with minimum hysteresis.
— The card is available in different versions according to the valve type and reference signal types.
— The front panel houses the leds for diagnostic and card operation, and a micro-USB port intended for card setup.

 

 
89255 | | |
 

PDE3G - Pressure control proportional valve - OBE

— The PDE3G* valve is a direct operated pressure control valve, with integrated electric proportional control and mounting interface in compliance with ISO 4401 standards.
— It is suitable to pilot two-stage valves, for pressure control in hydraulic circuits.
— Valves are available with different types of electronics, with analogue or fieldbus interfaces:

  • "GL" with digital integrated electronics for open loop and compact box; analogue, IO-link and CanOpen interfaces options available;
  • "GH" with digital integrated electronics for open loop with fieldbus communication.

— A solenoid current monitoring signal is available.
— Five pressure control ranges are available, up to 350 bar.
— The valves are easy to install. The driver manages digital settings directly.

 

NOTE: to download the PDF catalogue of the old series click here 

 
81221 | | |
 

PDE3J - Pressure control proportional valve for closed loop - OBE

— The PDE3J* valve is a direct operated pressure control valve with integrated electric proportional control and mounting interface in compliance with ISO 4401 standards.
— It is suitable to pilot two-stage valves, for pressure control in hydraulic circuits.
— It is available with different types of electronics, with analogue or fieldbus interfaces:

  • "JL" with digital integrated electronics for open loop and compact box; analogue, IO-link and CanOpen interfaces options available;
  • "JH" with digital integrated electronics for open loop with fieldbus communication.

— The monitoring of the value detected by the pressure transmitter is available on pin F.
— Three pressure adjustment ranges are available up to 350 bar .
— The valve is easy to install. The driver directly manages digital settings.

 

NOTE: to download the PDF catalogue of the old series click here 

 
81231 | | |
 

DS3GL - Solenoid operated directional valve with digital interfaces

— Directional valve with digital interface, solenoid actuated, with mounting surface according to ISO 4401-03 standards.
— The valve is supplied with 3 or 4 ways design, with 2 or 3 positions with a wide range of spools.
— The on-board electronics allow the valve to be controlled by a PLC with a low-power digital signal. There are several functions available, including fast switch, energy saving and soft-shift.
— The version with IO-Link interface effectively integrates the valve in a digital communication system driven by PLC, and allows collecting operational data and environmental information for predictive diagnostics.
— The valve is available with DC solenoids.
— The valve is also available with zinc-nickel coating on the body, that ensures a salt spray resistance up to 240 hours.
— Alternative to the standard manual override there are push, knob, push and twist, boot and mechanical detent devices.

 
41153 | | |
 

PRE3G - Pilot operated pressure control proportional valve - OBE

— The PRE3G* valve is a pilot operated pressure control valve with electric proportional control and mounting surface in compliance with ISO 4401 standards, controlled by an integral digital amplifier.
— It is suitable to modulate the pressure in hydraulic circuits.
— It is available with different types of electronics, with analogue or fieldbus interfaces:

  • "GL" with digital integrated electronics for open loop and compact box; analogue, IO-link and CanOpen interfaces options available;
  • "GH" with digital integrated electronics for open loop with fieldbus communication.

— Valves are easy to install. The driver directly manages digital settings.

 

NOTE: to download the PDF catalogue of the old series click here 

 
81251 | | |
 

EWM-SP-DAD - Card for axis control (stroke and pressure) with Profibus communication interface

This card has been developed for positioning control with integrated closed loop pressure where an high accuracy is needed, using a digital sensor for positioning, and analogue sensors for pressure sensing.

The card is an axis controller with two positioning control mode, SDD and NC. It communicates with the PLC via the integrated Profibus interface.

An integrated control for pressure limitation for one or two sensors (differential pressure), completes the card.

The output value, voltage or current type, has to be configured via software.

Card setup is via software only, through an USB-B port. Defined parameters can be configured via the Profibus interface.

CLICK HERE to download the start-up manual.

 

NOTE: to download the PDF catalogue of the old series click here 

 
89440 | | |
 

Connectors and cable set

Connectors and cable set for valves with integrated electronics

 
89000 | | |
 

PRE*G - Pilot operated pressure relief proportional valves - OBE

The PRE*G* valves are proportional pressure relief valves, pilot operated, with integrated electronics and mounting interface in compliance with ISO 6264 standards.

These valves are used to control hydraulic circuit pressure and enable the use of the full flow rate of the pump, even with settings approaching calibrated values.

The two-stage design and wide passages ensure reduced pressure drops thereby improving the system energy performance.

They are fitted with a manual pressure relief valve which is factory set to ≥ 15% of the maximum value in the pressure control range.

Valves are available with different types of electronics, with analogue or fieldbus interfaces.

They are available in three sizes with flow rates up to 500 l/min and in four pressure control ranges up to 350 bar.

The valves are easy to install. The driver directly manages digital settings.

NOTE: to download the PDF catalogue of the old series click here 

 
81321 | | |
 

M*F3(M) - Shut-off valves solenoid or hydraulically actuated, with or without position monitoring - Modular version - CETOP 03

M*F3 are shut-off valves, solenoid or hydraulically actuated, with or without spool position monitoring, in modular version, with mounting interface according to ISO 4401-03 standard.
Its are placed under directional control servovalves in order to guarantee the safety of circuit when a power failure occurs.

Spools with float, closed, parallel or cross position in de-energized condition are available.
Versions with spool monitoring do not have manual override and can not be disass-embled, because of their characteristics and their possible use on machinery subject to safety requirements.
The spool position monitoring is available either for initial position or for actuated position.

 
41270 | | | | 3D
 

PRE*J - Pilot operated pressure relief proportional valves for closed loop - with integrated electronics -OBE

PRE*J* valves are proportional pressure relief valves, pilot operated, with integrated electronics and pressure closed loop, with mounting interface in compliance with ISO 6264 standard.

These valves are used to control hydraulic circuit pressure and enable the use of the full flow rate of the pump, even with settings approaching calibrated values.

The two-stage design and wide passages ensure reduced pressure drops thereby improving the system energy performance.

They are fitted with a manual pressure relief valve which is factory set to ≥ 15% of the maximum value in the pressure control range.

Valves are available with different types of electronics, with analogue or fieldbus interfaces.

They are available in three sizes with flow rates up to 500 l/min and in four pressure control ranges up to 350 bar.

The valves are easy to install. The driver directly manages digital settings.

NOTE: to download the PDF catalogue of the old series click here 

 
81331 | | |
 

DDPE*J - Proportional directional control valves, pilot operated - OBE & Feedback

— The DDPE*J are proportional directional control valves, pilot-operated, with closed-loop position control of the main stage, with integrated electronics and with mounting interface in compliance with ISO 4401 standards.
— They are controlled directly by an integrated digital amplifier. Transducer and digital card allow a fine control of the positioning of the spool, reducing hysteresis and response times.
— They are available with different types of electronics, with analogue or fieldbus interfaces.
— A monitoring signal of the main spool position is available.
— The valves are easy to install. The driver directly manages digital settings.

 

 
83350 | | |
 

PZE3G - Proportional 3-way pressure reducing valve, pilot operated with integrated electronics

— PZE3G valve is a proportional 3-way pressure reducing valve, pilot operated, with on-board electronics with mounting surface according to ISO 4401- 03 standards.

— This valve controls the outlet pressure on port A, reducing the inlet pressure from line P or relieving the overpressure from line A into T keeping it at the set value. (typically: hydraulic counter-weight or load balancing)

— The valve is available with command signal in voltage or current and on board electronics with internal enable, external enable or 0V monitor on pin C. A monitor signal for solenoid current is available.

— The following versions are available, too:

  • "GL" with digital integrated electronics for open loop and compact box; analogue, IO-link and CanOpen interfaces options available;
  • "GH" with digital integrated electronics for open loop with fieldbus communication.

— The valves are easy to install. The driver manages the digital setting directly.

 
81502 | | |
 

PZE3J - Proportional 3-way pressure reducing valve, pilot operated, with pressure closed loop and integrated electronics

— PZE3J valve is a proportional 3-way pressure reducing valve, pilot operated, with pressure feedback, on-board electronics and mounting surface according to ISO 4401- 03 standards.

— This valve controls the outlet pressure on port A, reducing the inlet pressure from line P or relieving the overpressure from line A into T keeping it at the set value. (typically: hydraulic counter-weight or load balancing)

— The valve is available with command signal in voltage or current and on board electronics with internal enable, external enable or 0V monitor on pin C.

— The following versions are available, too:

  • "JL" with digital integrated electronics for open loop and compact box; analogue, IO-link and CanOpen interfaces options available;
  • "JH" with digital integrated electronics for open loop with fieldbus communication.

— The valves are easy to install. The driver manages the digital setting directly.

 

 
81503 | | |